Dedicated to bringing you the best High Performance Pontiac parts and accessories available on the market!

-  Pontiac Engine Builder  -

330-699-1358 

Best to contact us by email at:
sales_team@tinindianperformance.com

 

 

 

 

TIP digger goes 6.81 @ 192.28 Quickest NA Pontiac on the Planet!

The worlds  Quickest  Naturally Aspirated Pontiac
6.81 @ 192.28 mph
Kevin Swaney's Tin Indian Performance Rear Engine Dragster

- The fastest Pontiacs of all time listing -

 

 

Pontiac Pump Gas Street Engine Combinations

When building a killer Pontiac pump gas street engine, we feel that the combination of parts tends to be even more critical.  The parts need to match and compliment each other in order to optimize performance.  When building a Pontiac engine, the selection of cylinder heads, camshaft, and intake are critical to building the right combination and making maximum power from off idle to redline.   Having access to a Superflow 901 dynamometer for engine break in and tuning helps us get the most out of your combination in a very cost effective and thorough manner.  

We are a Pontiac engine builder that ONLY builds Pontiacs!  

New 80 cc High Port Pump Gas HR combo

Pump Gas 463 with KRE High Ports makes 580 HP and 590 ft lbs of torque!

This 463 cid Pontiac engine can be built with a stock Pontiac block or an MR-1 aftermarket block.  Engine uses a Comp Cam Tin Indian Performance custom ground hydraulic roller camshaft, Comp Cams Hydraulic roller lifters,  Eagle cast crankshaft, Eagle 6.625 rods, Federal Mogul rod and main bearings, Durabond cam bearings, Melling Oil pump, Edelbrock Victor, Pro Systems HP 1000 or 1050 Dominator carburetor, 1 7/8 header, 80 cc KRE Aluminum High Port Heads with NO port work or gasket match! 1.6 Scorpion rockers,  TIP Complete Gasket Set, TIP Viton rear main seal, Romac balancer, KB pistons, Total Seal Rings

The best times run with this current combination in a 1966 GTO weighing 3500 lbs is 11.077 @ 120.70 MPH!  The idel quality is very good and pulls over 13" of vac

Dyno Sheet

For more information on Kevin Swaney's 1966 GTO  / combination click here

475 Horsepower 553 ft lbs of Torque

461 cid Pontiac engine can be built with a stock Pontiac block or an MR-1 aftermarket block.  Engine uses a Crower hydraulic flat tappet cam,  PRO Sport Cast Crankshaft, PRO Sport 6.625 rods, Federal Mogul rod and main bearings, Durabond cam bearings, Melling Oil pump, Edelbrock Performer RPM intake, 850 Qjet carburetor, 1 3/4 header, Rhodes lifters, 85 cc KRE Aluminum D port heads (stock NO PORT WORK!) with total timing set at 31 deg!  Engine runs on pump gas.  TIP Complete Gasket Set, TIP Viton rear main seal, Romac balancer, SRP piston

Dyno Sheet

Can run high 11's very low 12's in a 3700 lb car with correct gearing and converter!


500 Horse 580 ft lbs of TORQUE Pump Gas Street Engine

463 cid Pontiac engine can be built with a stock Pontiac block or an MR-1 aftermarket block.  Engine uses a Crower hydraulic flat tappet cam,  Eagle Crankshaft, Eagle 6.625 rods, Federal Mogul rod and main bearings, Durabond cam bearings, Melling Oil pump, Edelbrock Performer RPM intake, 850 Qjet carburetor or Pro Systems HP950 carb, 1 3/4 header, Rhodes lifters, 85 cc KRE Aluminum D port heads (stock NO PORT WORK!) with total timing set at 31 deg!  Engine runs on pump gas.  TIP Complete Gasket Set, TIP Viton rear main seal, Professional Products balancer, KB forged  piston


520 Horse 585 ft lbs of TORQUE Pump Gas Street Engine

461 cid Pontiac engine can be built with a stock Pontiac block or an MR-1 aftermarket block.  Engine uses a Comp Cam Custom ground Hydraulic roller camshaft, Comp Cams Hydraulic roller lifters,  PRO Sport Cast Crankshaft, PRO Sport 6.625 rods, Federal Mogul rod and main bearings, Durabond cam bearings, Melling Oil pump, Edelbrock Performer RPM intake, 850 Holley carburetor, 1 3/4 header, Crower Hydraulic lifters, 85 cc KRE Aluminum D port heads gasket matched, 1.6 Scorpion rockers,  TIP Complete Gasket Set, TIP Viton rear main seal, Professional Producst balancer, Ross piston, Total Seal Rings

11.50s in a 3700 lb with correct converter and gear


550 Horse 580 ft lbs of TORQUE Pump Gas Street Engine

This 468 makes 550 hp @ 5300 rpm and 580 ft lbs of torque with the following components:  74cc KRE 310 cfm Aluminum D port heads, Eagle Rods, Total Seal Rings, Ross Pistons, TIP Gaskets,  Professional Product SFI damper, Crower hyd flat tappet cam, 1.75" Hedman Headers, Scorpion Rockers, Torker II intake, and 850 Demon on pump gas.  Pro Street idle 

Dyno Sheet

Low 11's in a 3500 lb car


552 HP / 584 ft lbs of torque HR Pump Gas Engine

This 468 makes 552 hp @ 5400 rpm and 584 ft lbs of torque @ 4400 rpm with the following components:  74cc KRE 310 cfm Aluminum D port heads, Eagle Rods, Total Seal Rings, SRP Pistons, Eagle Cast crankshaft, TIP Gaskets,  Professional Product SFI damper, TIP Custom ground Comp Cams Hydraulic Roller camshaft with Comp Cams hydraulic roller lifters,  Scorpion Rockers,  1 /3/4 Doug's Headers, Hurricane intake, and 950 Holley HP carb n pump gas.  Idels at 800 rpm with noticeable lope.

Dyno Sheet


600 HP  / 596 ft lbs of torque Pump Gas Engine

 

This 462 makes 600 hp @ 5800 rpm and 596 ft lbs of torque @ 4700 rpm.  Engine pulls 13.9 inches of vacuum at 950 rpm.  We used the following components:  72cc 325 cfm Edelbrock Aluminum heads, Eagle Rods, Total Seal Rings, Ross dished Pistons, Pro Sport Forged, TIP Gaskets,  Professional Product SFI damper, TIP Custom ground Comp Cams Solid Roller camshaft with Crower roller lifters,  Harland Sharp rockers,  2" Headers, Victor intake, and Holley HP1000 carb on pump gas.   

Dyno Sheet

high 10s in a 3500 lb car

300 rpm pull on Brian Frank's 462 Brian Frank's 462 ideling before a dnyo pull


650 HP Pump Gas Engine

As seen in High Performanc Pontiac

PUMP GAS POUNDER - Will TIP's 400 Block / KRE Headed combo produce more than 600 HP on 93 Octane? - by John Carollo Photography by the Author

PDF version of Article

Dyno Sheet

 

mid 10s in a 3500 lb car


800 HP / 796 ft lbs of torque E85 Engine

511 cid MR-1A E85 Blower Combo

Dyno Sheet

This 511 makes 801 hp @ 5900 rpm and 796 ft lbs of torque with the following components:  MR-1a Aluminum block, 80cc KRE High Port heads, Scorpion rockers, TIP Custom Ground Comp hyd roller cam and valve train, Meziere electric water pump, Ross  Pistons, Total Seal rings, ATI Balancer,  Moroso pan, BDS intake, two 850 E85 4150 style carbs, TIP gaskets, TIP Viton Seal, SCAT forged crank, Crower rods, TIP logo valve covers, 8-71 blower, Taylor wires, MSD Distributor

Starting at $22,500

 

 

 

This is Jason Crawford's blown 511 MR-1A / KRE 80 cc High Port combo warming up for a dyno pull

This is Jason Crawford's blown 511 MR-1A combo making 801 hp and 796 ft lbs of torque on E85


680 HP / 659 ft lbs of torque Pump Gas Engine 

Dyno Sheet

This 505 makes 685 hp @ 6100 rpm and 658 ft lbs of torque with the following components:  MR-1 block, 85cc 340 cfm KRE D port heads, Scorpion rockers, TIP Custom Ground Comp solid roller cam and valve train, Meziere electric water pump, Ross  Pistons, Total Seal rings, Romac Balancer,  Moroso pan, Victor intake, 1050 Dominator, TIP gaskets, TIP Viton Seal, Crower billet crank, Crower rods, TIP Crank mandrel system, Moroso 4 vane vac pump, TIP logo valve covers, KRE stud girdle, Taylor wires, MSD Distributor

Starting at $13,900


We can rebuild your Pontiac engine with just about any modifications that you desire. From mild to wild, from pure stock to high performance, we can do it!  We specialize in high horse power Pontiac engines.  

Call 330-699-1358 for details or email us for a detailed quote.

Looking for a RACE engine packages click here                  


If you have any questions please email us at sales_team@tinindianperformance.com and we will get right back to you.

HomeProducts  | Online Catalog | Engine CombinationsContact Us  |  Links  |  Cars and Photos | Buick Performance Parts  |  Oldsmobile Performance PartsTerms/General Info

We accept Mastercard!     We accept Discover!    We accept Visa!    We accept Paypal!

2004 Tin Indian Performance, LTD
P.O. Box 1162, Uniontown, Ohio 44685